Frame relay multipoint lab: Difference between revisions

From ITCwiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 12: Line 12:


==Phase Two==
==Phase Two==
You will want to do the basics on Routers like:
First run your basic configurations on the routers:
*Hostname
*Hostname
*Address your Fast Ethernet ports so they can recieve some mail.
*Address your FastEthernet ports
*No ip domain-lookup
*No ip domain-lookup
*Some Banner action
*Set up a Banner
*Password the crap out of your router so demons dont get you while you sleep at night!
*Password protect your devices
==Phase Three==
==Phase Three==
This phase will be all about how to setup your frame relay on your routers. We will be starting on R1 so please be there. You will start off by going into global config mode.
This phase will be all about how to setup your frame relay on your routers. We will be starting on R1. You will start off by going into global config mode.
*interface s0/0/0
*interface s0/0/0
*encapsulation frame-relay
*encapsulation frame-relay
Line 25: Line 25:
*ip address 192.168.0.1 255.255.255.0
*ip address 192.168.0.1 255.255.255.0
*frame-relay interface-dlci 103
*frame-relay interface-dlci 103
*exit (out of the dlci command interface thingy)
*exit
*frame-relay interface-dlci 102
*frame-relay interface-dlci 102
*exit
*exit
Line 43: Line 43:
*frame-relay interface-dlci 301
*frame-relay interface-dlci 301
*ip ospf network point-to-multipoint
*ip ospf network point-to-multipoint
Your network should be able to ping each other at this point in time.
At this point a ping should be successful on your directly connected devices.
==Phase Five==
==Phase Five==
Time for some OSPF action. We already set up the OSPF point-to-multipoint in the sub-interfaces. Now you will set up OSPF the same way you always to do but now you will enter the following command.
Configuring OSPF. We already set up the OSPF point-to-multipoint in the sub-interfaces.  
Set up OSPF.
*(R2)router ospf 1
*(R2)network 10.2.2.0 0.0.0.255 area 0
*(R2)network 192.168.0.0 0.0.0.255 area 0
Set up other routers with thier correct networks as well.
Now you will set up OSPF with these extra commands.
*(R2 in ospf)neighbor 10.2.2.0 cost 100 (This is saying who your neighbors are)
*(R2 in ospf)neighbor 10.2.2.0 cost 100 (This is saying who your neighbors are)
*(R3 in ospf)neighbor 10.3.3.0 cost 100
*(R3 in ospf)neighbor 10.3.3.0 cost 100

Revision as of 17:07, 8 December 2010

Frame Relay Multipoint Lab

Diagram.jpeg

Goals of this lab

  • To create a network using Multipoint Frame Relay
  • Achieve Frame Relay using the Adtran Atlas 550
  • Configure OSPF for multipoint routing

Phase One

Connect the network according to the diagram. You will need to pay attention to which ports you use on the Adtran as this is be your DLCI numbers. For this lab we will be using Port 1 of the Adtran for R1, Port 2 for R2, and Port 3 for R3. Below is how you determine what is going on with the Adtran.

Portnum.JPG Table.JPG

Phase Two

First run your basic configurations on the routers:

  • Hostname
  • Address your FastEthernet ports
  • No ip domain-lookup
  • Set up a Banner
  • Password protect your devices

Phase Three

This phase will be all about how to setup your frame relay on your routers. We will be starting on R1. You will start off by going into global config mode.

  • interface s0/0/0
  • encapsulation frame-relay
  • interface s0/0/0.1 multipoint
  • ip address 192.168.0.1 255.255.255.0
  • frame-relay interface-dlci 103
  • exit
  • frame-relay interface-dlci 102
  • exit
  • ip ospf network point-to-multipoint (So OSPF will work in this enviroment)

Now on R2 in global configuration mode

  • interface serial0/0/0
  • encapsulation frame-relay
  • interface s0/0/0.1 point-to-point
  • ip address 192.168.0.2 255.255.255.0
  • frame-relay interface-dlci 201
  • ip ospf network point-to-multipoint

Now on R3 in global configuration mode

  • interface serial0/0/0
  • encapsulation frame-relay
  • interface s0/0/0.1 point-to-point
  • ip address 192.168.0.3 255.255.255.0
  • frame-relay interface-dlci 301
  • ip ospf network point-to-multipoint

At this point a ping should be successful on your directly connected devices.

Phase Five

Configuring OSPF. We already set up the OSPF point-to-multipoint in the sub-interfaces. Set up OSPF.

  • (R2)router ospf 1
  • (R2)network 10.2.2.0 0.0.0.255 area 0
  • (R2)network 192.168.0.0 0.0.0.255 area 0

Set up other routers with thier correct networks as well. Now you will set up OSPF with these extra commands.

  • (R2 in ospf)neighbor 10.2.2.0 cost 100 (This is saying who your neighbors are)
  • (R3 in ospf)neighbor 10.3.3.0 cost 100

Troubleshooting and Documentation

Your lab is now complete and you should be able to ping everything from everything. Your routing tables should have the 10.2.2.0 and 10.3.3.0 networks. Once you are done you may clean up and go have your self a very pleasant day and remember cisco is very very sneakie. :) AND DONT FORGET TO REFLECT!

Retrieved from "https://wiki.ihitc.net/mediawiki/index.php?title=Frame_relay_multipoint_lab&oldid=3592"