IPv6 Routing Protocol Configurations

Static Routing

Command	Description
ipv6 route ipv6-prefix/prefix-length {ipv6-address | interface-type interface-number [ipv6-address]} [administrative-distance] [administrative-multicast-distance | unicast | multicast] [tag tag] Example: Router(config)# ipv6 route ::/0 serial 2/0	Configures a static IPv6 route A static default IPv6 route is being configured on a serial interface. See the syntax examples that immediately follow this table for specific uses of the ipv6 route command for configuring static routes.

Summary Steps

1. enable
2. configure terminal
3. ipv6 route ipv6-prefix/prefix-length {ipv6-address | interface-type interface-number

[ipv6-address]} [administrative-distance] [administrative-multicast-distance | unicast | multicast] [tag tag]

RIPng

Command	Description
ipv6 unicast-routing Example: Router(config)# ipv6 unicast-routing	Enables the forwarding of IPv6 unicast datagrams
ipv6 rip name enable Example: Router(config-if)# ipv6 rip process1 enable	Enables the specified IPv6 RIP routing process on an interface
maximum-paths number-paths Example: Router(config-router)# maximum-paths 1	(Optional) Defines the maximum number of equal-cost routes that IPv6 RIP can support The number-paths argument is an integer from 1 to 64. The default for RIP is four paths.
ipv6 router rip word Example: Router(config)# ipv6 router rip process1	Configures an IPv6 RIP routing process and enters router configuration mode for the IPv6 RIP routing process. Use the word argument to identify a specific IPv6 RIP routing process
ipv6 rip name default-information {only \ originate} [metric metric-value] Example: Router(config-if)# ipv6 rip process1 default-information originate	(Optional) Originates the IPv6 default route (::/0) into the specified RIP routing process updates sent out of the specified interface.

Summary Steps

1. enable
2. configure terminal
3. ipv6 router rip word
4. maximum-paths number-paths
5. exit
6. interface type number
7. ipv6 rip name default-information {only | originate} [metric metric-value]

IS-IS

Command	Description
router isis area-tag Example: Router(config)# router isis area2	Enables IS-IS for the specified IS-IS routing process, and enters router configuration mode.
net network-entity-title Example: Router(config-router)# net 49.0001.0000.0000.000c.00	Configures an IS-IS network entity title (NET) for the routing process.
ipv6 router isis area-name Example: Router(config-if)# ipv6 router isis area2	Enables the specified IPv6 IS-IS routing process on an interface. configuration mode

OSPFv3

Command	Description
router ospfv3 [process-id] Example: Router(config)# router ospfv3 1	Enables OSPFv3 router configuration mode for the IPv4 or IPv6 address family.
nssa | stub] Example: Router(config-router)# area 1	Configures the OSPFv3 area.
auto-cost reference-bandwidth Mbps Example: Router(config-router)# auto-cost reference-bandwidth 1000	Controls the reference value OSPFv3 uses when calculating metrics for interfaces in an IPv4 OSPFv3 process.
bfd all-interfaces Example: Router(config-router)# bfd all-interfaces	Enables BFD for an OSPFv3 routing process
virtual-link router-id]} [default-information originate [always | metric | metric-type | route-map] | distance | distribute-list prefix-list prefix-list-name {in | out} [interface] | maximum-paths paths | redistribute protocol | summary-prefix ipv6-prefix] Example: Router(config-router)# default area 1	Returns an OSPFv3 parameter to its default value.
ignore lsa mospf Example: Router(config-router)# ignore lsa mospf	Suppresses the sending of syslog messages when the router receives LSA Type 6 multicast OSPFv3 packets, which are unsupported.
interface-id snmp-if-index Example: Router(config-router)# interface-id snmp-if-index	Configures OSPFv3 interfaces with Simple Network Management Protocol (SNMP) MIB-II interface Index (ifIndex) identification numbers in IPv4 and IPv6.
log-adjacency-changes [detail] Example: Router(config-router)# log-adjacency-changes	Configures the router to send a syslog message when an OSPFv3 neighbor goes up or down.
passive-interface [default interface-type interface-number] Example: Router(config-router)# passive-interface default	Suppresses sending routing updates on an interface when using an IPv4 OSPFv3 process.
queue-depth {hello update} {queue-size unlimited} Example: Router(config-router)# queue-depth update 1500	Configures the number of incoming packets that the IPv4 OSPFv3 process can keep in its queue.
router-id {router-id} Example: Router(config-router)# router-id 10.1.1.1	Use a fixed router ID.

Summary Steps:

1. enable

2. configure terminal

3. router ospfv3 [process-id]

4. address-family ipv6 unicast

5. area area-ID range ipv6-prefix/prefix-length

6. default {area area-ID [range ipv6-prefix | virtual-link router-id]} [default-information originate [always | metric | metric-type | route-map] | distance | distribute-list prefix-list prefix-list-name {in | out} [interface] | maximum-paths paths | redistribute protocol | summary-prefix ipv6-prefix]

7. default-information originate [always | metric metric-value | metric-type type-value | route-map map-name]

8. default-metric metric-value

9. distance distance

10. distribute-list prefix-list list-name {in [interface-type interface-number] | out routing-process [as-number]} 11. maximum-paths number-paths

12. summary-prefix prefix [not-advertise | tag tag-value]

EIGRP

Command	Description
ipv6 unicast-routing Example: Router(config)# ipv6 unicast-routing	Enables the forwarding of IPv6 unicast datagrams
ipv6 eigrp as-number Example: Router(config-if)# ipv6 eigrp 1	Enables EIGRP for IPv6 on a specified interface
ipv6 router eigrp as-number Example: Router(config-if)# ipv6 router eigrp 1	Enters router configuration mode and creates an EIGRP IPv6 routing process
show ipv6 eigrp [as-number] interfaces [type number] [detail] Example: Router# show ipv6 eigrp interfaces	Displays information about interfaces configured for EIGRP for IPv6.

Summary Steps

1. enable
2. configure terminal
3. ipv6 unicast-routing
4. interface type number
5. no shut
6. ipv6 enable
7. ipv6 eigrp as-number
8. ipv6 router eigrp as-number
9. eigrp router-id ip-address
10. exit
11. show ipv6 eigrp [as-number] interfaces [type number] [detail]