View source for IOS vs. CatOS: Basic Configuration

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|







=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.



In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
!  IOS Command
!  CatOS Command
|-
!Privileged
|  Enable
|  Enable
|-
!Interface
|  (config-t)interface ''int'' (which puts you into interface configuration mode)
|  (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
|  (config-line)password ''password''
|  (enable)set password (you will be prompted to change password)
|-
!Turn on ports
|  (config-int)no shutdown
|  (enable)set port enable ''mod/port''
|-
!Turn off ports
|  (config-int)shutdown
|  (enable)set port disable ''mod/port''
|-
!Banner-MOTD
|  (config-t)banner-motd # ''banner here'' #
|  (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
|  (config-t) 
|  (enable)clear banner motd
|-
!System / Hostname
|  (config)hostname ''name''
|  (enable)set system name ''name''
|-
!Set Idle Logout time
|  (config-t) 
|  (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
|  (config-int)bandwidth ''number in kb''
|  (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
|  (config-t)vtp domain ''domain-name''
|  (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
|  (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
|  (enable)set vlan ''number'' state ''active''
|-
!VLAN names
|  (config-vlan)name ''name''
|  (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
|  (config-t)no vlan ''number'' 
|  (enable)clear vlan ''number''
|-
!Enabling Trunking
|  (config-int)switchport mode trunk 
|  (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
|  (config-int)no switchport mode trunk 
|  (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
|  (enable)delete flash:''filename'' 
|  (enable)delete bootflash:''filename''
|-
!Spanning-Tree
|  (config-t)spanning-tree ''vlan''
|  (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|ping
|ping
|-
!
|tracert
|traceroute
|-
!
|show run
|show running-config all
|-
!
|copy run start
|copy config
|-
!
|erase start
|clear config all
|-
|}
__NOTOC__