Franske ITC-2000 Assignments
Labs
You are responsible for completing ALL of these labs. You must submit a lab report for each topic/chapter (you should combine multiple labs from the chapter/topic into a single report). If you work with a partner on a lab you only need to submit a single lab report for the two of you but it must have both your names on it. Each lab report is worth up to 20 points. This falls into the Labs/Homework category of your course grade.
PC Disassembly/Reassembly Labs
- 1.3.2.2 Lab - Disassemble a Computer
- 2.1.2.5 Lab - Install the Power Supply
- 2.1.3.10 Lab - Install the Motherboard in a Computer
- 2.1.4.7 Lab – Install the Drives
- 2.1.5.6 Lab - Install Adapter Card
- 2.1.7.4 Lab - Install Internal Cables
- 2.1.7.8 Lab - Install the Front Panel Cables
- 2.1.7.11 Lab – Complete the Computer Assembly
Chapter 3 Labs
- 3.1.1.6 Lab - Investigate BIOS or UEFI Settings
- 3.1.2.5 Lab - Search for BIOS or UEFI Firmware Updates
- 3.1.2.6 Lab - Install Windows
- NOTE: Be sure to choose a new installation, not to repair an existing one. If prompted choose to install "Windows 10 Enterprise". Also, choose to do a "Custom" installation, not an upgrade, and delete all existing partitions.
- NOTE: Make sure your computer is NOT connected to the Internet while Windows is being installed so that you can create a local account instead of being forced to use a Microsoft account!
- NOTE: During the account creation process use the name "ITC Admin" and the password "Password123!" be sure to write them down and have your partner write them down as well because you will need them again later in the course.
- 3.1.2.7 Lab - Install Third-Party Software in Windows
Chapter 4 Labs
- 4.2.3.6 Lab – Troubleshoot Hardware Problems
- NOTE: In this lab you are asked to troubleshoot any problems with your hardware. After making sure your system is working properly obtain sheets from the instructor with a series of problems to create for your partner. Be sure to have your partner leave the room while you are creating each problem (one problem at a time!).
Chapter 6 Labs
- 6.1.2.7 Lab - Configure a NIC to Use DHCP in Windows
- NOTE: Do NOT connect your router to an Internet connection, it's not required for this lab.
- 6.1.3.10 Lab - Configure a Wireless Network
- NOTE: Do NOT connect your router to an Internet connection, it's not required for this lab.
- NOTE: Change the router settings as indicated in the lab, use these for the NEW settings:
- Router IP Address: 172.17.99.1
- Router Subnet Mask: 255.255.255.0
- Router Name: ITE-Rxx (replace xx with the number of one of your PCs, found on a sticker on top of the classroom PC under your desk)
- DHCP Starting IP Address: 172.17.99.21
- DHCP Maximum Number of Users: 20
- Router Username: admin
- Password: Password123!
- Wireless SSID: ITE-Wxx (replace xx with the number of one of your PCs, found on a sticker on top of the classroom PC under your desk)
- Wireless Passphrase: Cisco456!
- NOTE: Do not complete Part 4 of this lab which is listed as optional.
- 6.1.4.8 Lab - Configure Firewall Settings
- NOTE: Do NOT connect your router to an Internet connection, it's not required for this lab.
- NOTE: In Part 2, Step 1 you should add the MAC addresses of both your computers to the allowed list of MACs on the router.
- NOTE: In Part 2, Step 2 you should add the IP address of ONE of your computers to the DMZ on the router.
- NOTE: In Part 2, Step 3 you should add a pot forwarding rule to forward port 80 to the IP address of the OTHER one of your computers. Also note that different manufacturers call "port forwarding" different things. For example TP-Link calls it "virtual servers" instead in some models of routers.
- 6.2.2.5 Lab - Troubleshoot Network Problems
- NOTE: In this lab you will connect your router to an Internet connection, in room B-107 please use the GREEN network jack under your desk to make this connection.
- NOTE: Obtain sheets with two lists of problems to create from the instructor. Create these problems for your partner one at a time while they are out of the room and ask them to fix your network. If you are unsure of how to create the issue ask your instructor for help.
- NOTE: Before you leave today please reset your router to the factory default settings.
Chapter 8 Labs
- 8.3.1.3 Lab - Install a Printer in Windows
- 8.4.1.3 Lab - Share a Printer in Windows
- NOTE: In this lab use a laptop as the second device (the one which is not directly connected to the printer). Both the laptop and your desktop will need to be connected to the same network so setup your network routers with a connection to both computers.
- 8.5.3.2 Lab - Perform Preventive Maintenance on a Laser Printer
- NOTE: In this lab you will not actually install any new parts, just find and remove the existing parts on the printer and then re-install them. Also, uou should locate the fuser on the printer and find and watch a video showing how to remove and replace it but do not actually do it because on our particular printer model it requires disassembling most of the printer to get to the fuser.
- Lab - Setup and Connect to Network Printers
Chapter 9 Labs
- 9.1.2.5 Lab - Install Linux in a Virtual Machine and Explore the GUI
- NOTE: Before you create your VM please make sure that VirtualBox is set to save VMs into a folder on the D:\ drive that contains the semester and year in the folder name such as D:\bfranske-fa17\
- NOTE: Change the network jack your PC is plugged into at your desk to the "ITC network" (the GREEN network jack in B107). Make sure to change it back to the "Campus" connection (the RED network jack in B107) before you leave!
- NOTE: The Ubuntu installation ISO image file is located in the D:\CNT Files folder. The version of Ubuntu in this folder may be newer than the version listed in the lab
- NOTE: Set your virtual machine to use at least 2 GB of RAM (for a faster VM you could go higher as long as you stay in the green zone) and have at least an 18 GB virtual hard drive.
- NOTE: Make sure to set your virtual machine to use bridged networking before starting it
- If you have time you may want to try a different distribution of Linux to see what is the same and what's different. The D:\CNT Files folder should contain some others such as Linux Mint or Debian you can try as well. Just setup a new virtual machine for each one you would like to try.
- Don't forget to change the network jack your PC is plugged into at your desk back to the "Campus" connection (the RED network jack in B107) before you leave!
Chapter 10 Labs
- 10.3.1.1 Lab - Windows Installation
- NOTE: Be sure to leave at least 10GB of unpartitioned space during the installation! Try to figure out how to leave this unpartitioned space at the END of the drive.
- NOTE: Make sure your computer is NOT connected to the Internet while Windows is being installed so that you can create a local account instead of being forced to use a Microsoft account!
- NOTE: During the account creation process use the name "ITC Admin" and the password "Password123!" be sure to write them down and have your partner write them down as well because you will need them again later in the course.
- 10.2.1.8 Lab - Create a Partition in Windows
- NOTE: Do this lab AFTER the Windows Installation lab!
- 10.3.1.4 Lab - Finalize the Windows Installation
Chapter 11 Labs
- 11.1.2.10 Lab - Explore the Windows Desktop
- 11.1.3.4 Lab - Work with Task Manager
- 11.1.4.11 Lab - Working with File Explorer
- 11.2.1.5 Lab - Explore Control Panel Categories
- 11.2.2.3 Lab - User Accounts
- 11.2.3.5 Lab - Configure Browser Settings
- 11.2.5.8 Lab - Manage Virtual Memory
- 11.2.6.2 Lab - Use Device Manager
- 11.2.7.4 Lab - Region and Language Options
- 11.3.1.11 Lab - Monitor and Manage System Resources
- 11.3.2.7 Lab - System Utilities
- 11.3.2.8 Lab - Manage System Files
- 11.3.3.8 Lab - Hard Drive Maintenance
- 11.3.4.6 Lab - Install Third-Party Software
- 11.4.1.5 Lab - Work in the Windows Command Shell
- 11.4.2.7 Lab - File System Commands
- 11.4.3.2 Lab - Disk CLI Commands
- 11.4.4.2 Lab - Task and System CLI Commands
- 11.4.5.3 Lab - Other Useful Commands
- 11.5.2.4 Lab - Share Resources
- 11.5.4.2 Lab - Connect and Test the Wireless Connection
- 11.5.6.2 Lab - Windows Remote Desktop and Assistance
- 11.6.1.2 Lab - Manage the Startup Folder
- 11.6.1.5 Lab - Schedule a Task using the GUI and the Command Line
- 11.6.2.4 Lab - System Restore and Hard Drive Backup
- 11.7.3.2 Lab - Troubleshoot Operating System Problems
Chapter 12 Labs
- Check out an Android tablet from your instructor.
- The access PIN on the tablets is "1 2 3 4"
- 12.1.2.2 Lab - Working with Android
- 12.1.4.4 Lab - Mobile Device Features
- 12.2.1.2 Lab – Passcode Locks
- Make sure you set the PIN back to "1 2 3 4" when you are done with the lab if you have changed it!
- 12.4.2.4 Lab - Troubleshoot Mobile Devices
Chapter 13 Labs
- 13.2.3.7 Lab - Bitlocker and Bitlocker To Go
- 13.3.2.5 Lab - Configure Windows Local Security Policy
- 13.3.3.6 Lab - Configure Users and Groups in Windows
- 13.3.4.6 Lab - Configure Windows Firewall
- 13.5.2.2 Lab - Document Customer Information in a Work Order
Chapter 14 Labs
- 14.4.1.4 Lab - Remote Technician - Fix a Hardware Problem
- 14.4.1.5 Lab - Remote Technician - Fix an Operating System Problem
- 14.4.1.6 Lab - Remote Technician - Fix a Network Problem
- 14.4.1.7 Lab - Remote Technician - Fix a Security Problem
- 14.4.2.7 Lab - Write Basic Scripts in Windows and Linux
Homework
Any homework assigned in the course will go here. This falls into the Labs/Homework category of your course grade. Remember, for homework assignments turn in the actual pages from your lab book or printouts from the curriculum and not a lab report. Homework assignment are individual, you and your lab partner need to both turn them in separately even if you work on them together.
- Participate in an online forum discussion (typically 3 quality posts or more) of each chapter on the NetSpace site. See forum posting page for details. (up to 10 points each chapter based on quality)
Participation Activities
Any participation activities completed in the course will go here. This falls into the participation category of your course grade.
- Attend at least two Student Success Day presentations and bring proof of attendance signed by each presenter (10 points)
- Meet with an academic advisor (10 points for meeting)
- Complete a program/degree plan (10 points for completing)
- Complete the online course feedback form (5 points for completing)
- Complete the Practice Final Exam (Chapters 1-9) (10 points for attempting)
- Complete the Practice Final Exam (Chapters 10-14) (10 points for attempting)
- Compete the A+ 220-1001 Certification Practice Exam (10 points for attempting)
- Compete the A+ 220-1002 Certification Practice Exam (10 points for attempting)
Unit Assessments
You are responsible for completing the online exam associated with each chapter in the course through the NetSpace website. This category will also include periodic checkpoint exams covering a group of chapters.
- Chapter 1 Exam
- Chapter 2 Exam
- Chapter 3 Exam
- Chapter 4 Exam
- Certification Checkpoint Exam #1 (Chapters 1 - 4)
- Chapter 5 Exam
- Chapter 6 Exam
- Certification Checkpoint Exam #2 (Chapters 5 - 6)
- Chapter 7 Exam
- Chapter 8 Exam
- Certification Checkpoint Exam #3 (Chapters 7 - 8)
- Chapter 9 Exam
Online Final Exams
The final exam category of your grade includes the following exams
- Final Exam (Chapters 1-9)
- Final Exam (Chapters 10-14)
Skills Final Exam
The Skills Final Exam is designed to test your ability to apply the concepts learned in this class and practiced in labs to common, real-world scenarios.