STP Study Guide All: Difference between revisions

From ITCwiki
Jump to navigation Jump to search
 
(2 intermediate revisions by the same user not shown)
Line 38: Line 38:


• The protocol establishes one root port on each nonroot bridge.
• The protocol establishes one root port on each nonroot bridge.
• The root port is the lowest-cost path from the nonroot bridge to the root bridge
• The root port is the lowest-cost path from the nonroot bridge to the root bridge


Line 113: Line 114:


MST
MST
PortFast
Spanning Tree Portfast causes an interface configured as a layer 2 access port to enter the forwarding state immediately.
Conf t
int fa 0/1
spanning-tree portfast
confirm with show spanning-tree interface Fastethernet 0/1.


='''Config the Basic Parameters of PVRST+'''=
='''Config the Basic Parameters of PVRST+'''=
Line 138: Line 127:
='''PortFast'''=
='''PortFast'''=


Spanning Tree Portfast causes an interface configured as a layer 2 access port to enter the forwarding state immediately. Conf t int fa 0/1 spanning-tree portfast
Spanning Tree Portfast causes an interface configured as a layer 2 access port to enter the forwarding state immediately.  
 
Conf t int fa 0/1 spanning-tree portfast
 
confirm with show spanning-tree interface Fastethernet 0/1.
confirm with show spanning-tree interface Fastethernet 0/1.
Config the Basic Parameters of PVRST+ conf t spanning-tree mode rapid-pvst spanning-tree vlan 2 root primary spanning tree- vlan 3 root secondary
Config the Basic Parameters of PVRST+ conf t spanning-tree mode rapid-pvst spanning-tree vlan 2 root primary spanning tree- vlan 3 root secondary



Latest revision as of 15:31, 6 February 2012

By Andrew Westin


Spanning Tree Sudy Guide

Evolution of STP Basics Evolution of STP What is STP? (Spanning Tree Protocol) – Eliminates loops at layer 2 topology


There are many varieties of STP...[pg 120]

DEC STP 802.1D Common Spanning Tree (CST) Per VLAN Spanning Tree Plus+ Rapid STP (RSTP)/IEEE 802.1w Multiple Spanning Tree(MST) PVRST+

STP initially converges on a logically loop-free network topology

1) Elects one root bridge

2) Selects the root port on all nonroot bridges

3) Selects the designated port on each segment

Elects One Root Bridge

• The protocol uses a process to elect a root bridge

• Only one bridge acts as the root bridge in a given network per VLAN

• On the root bridge, all ports act as designated ports

• Switch with lowest priority parameter is elected as root

• STP Step 2 (cont)

Selects the Root Port on All Non-root Bridges

• The protocol establishes one root port on each nonroot bridge.

• The root port is the lowest-cost path from the nonroot bridge to the root bridge

Selects Designated Port on Each Segment

• On each segment, STP establishes one designated port on the bridge that has the lowest path cost to the root bridge • The switch primarily chooses a designated port as the least-cost path to the root bridge • In the event of a tie, the bridge ID acts as the tiebreaker • Port Roles

There are four roles of ports under STP

1) Root

2) Designated

3) Non-Designated

4) Disabled

There are Five Port States

• Blocking

• Listening

• Learning

• Forwarding

• Disabled

RSTP

A variation of Spanning Tree Protocol (STP) designed to ensures a topology that doesn’t have loops.

IEEE introduced Rapid Spanning Tree Protocol (RSTP) as 802.1w

Detection of root switch failure is done in 3 hello times STP can take 30 to 50 seconds to respond to a topology change, RSTP is typically able to respond to changes within 3 × Hello times *(default: 3 times 2 seconds) or within a few milliseconds of a physical link failure RSTP maintains backup details regarding the discarding status of ports.

RSTP bridge port roles:

Root - A forwarding port that is the best port from Non root-bridge to Root bridge

Designated - A forwarding port for every LAN segment

Alternate - An alternate path to the root bridge. This path is different than using the root port.

Backup - A backup/redundant path to a segment where another bridge port already connects.

Disabled - Not strictly part of STP, a network administrator can manually disable a port

RSTP Topology Change Mechanism

When an RSTP bridge detects a topology change it performs the following actions. The RSTP Bridge starts the TC while time with a value equal to twice the hello time for all its non-edge designated ports and its root, port if necessary. The TC While time is the interval during which the RSTP Bridge actively informs the rest of the bridges in the network of a topology. It then flushes the MAC addresses associated with all non-edge ports. And as long as the TC While timer is running the BPDUs will be sent out of the port will have the TC bit set.

Bridge Identifier for PVRST+

Bridge Priority A 4-bit field still used to carry bridge priority

Extended System ID

Mac Address

Only four high-order bits of the 16 bit bridge priority field carry actual priority

Cisco STP Default Config

PVST+

PVRST+

MST

Config the Basic Parameters of PVRST+

conf t

spanning-tree mode rapid-pvst

spanning-tree vlan 2 root primary

spanning tree- vlan 3 root secondary

PortFast

Spanning Tree Portfast causes an interface configured as a layer 2 access port to enter the forwarding state immediately.

Conf t int fa 0/1 spanning-tree portfast

confirm with show spanning-tree interface Fastethernet 0/1.

Config the Basic Parameters of PVRST+ conf t spanning-tree mode rapid-pvst spanning-tree vlan 2 root primary spanning tree- vlan 3 root secondary

Multiple Spanning Tree

MST extends the IEEE 802.1w RST algorithm to multiple spanning trees. The main purpose of MST is to reduce the total number of spanning-tree instances.