Cisco Shortcut Guide

Basic Tips

Use the up arrow to bring up your last entered commands and the down arrow to go back. Type ? to see the list of possible commands and your current prompt Use the home key on your keyboard to bring your cursor to the beginning of the command you're typing. You can use the end key to go back to the end.

Do you want to get out of a long list without having to scroll through everything? (For example show run) Instead of hitting the space bar repeatedly just type the letter q Are you in a config mode and wish to issue a show command? Just put the word do in front of your command Router(config)#do show run Do the following to keep those pesky log messages from disrupting your typing: Router(config)#line con 0 Router(config-line)#logg syn

Hit the tab key to automatically complete a command you are typing. To quickly cancel a ping use Ctrl-Shift-6

The following examples will have full versions of common commands next to the shortest versions(These will not necessarily work on all versions of routers or switches).

Clear the Configurations

Switch>enable Switch#erase startup-config Switch#delete flash:vlan.dat (This step only needed for switches that have vlans added) Switch#reload

Switch>en Switch#e s Switch#del vlan.dat Switch#rel

Basic Configurations

Router#configuration terminal Router(config)#enable secret cisco Router(config)#banner motd #Authorized access only!# Router(config)#line console 0 Router(config-line)#password class Router(config-line)#login Router(config-line)#no ip domain-lookup Router(config)#hostname R1 R1(config)#copy running-config startup-config

Router#conf t Router(config)#ena s cisco Router(config)#ban m #Authorized access only!# Router(config)#lin c 0 Router(config-line)#pas class Router(config-line)#logi Router(config-line)#no ip domain-lo Router(config)#ho R1 R1(config)#cop ru st

Assign Addresses

Router#configuration terminal Router(config)#interface fastethernet 0/0 Router(config-if)#ip address 192.168.1.1 255.255.255.0 Router(config-if)#description Crossover cable to R2 Router(config-if)#no shutdown Router(config-if)#interface serial 0/0/0 Router(config-if)#ip address 192.168.2.1 255.255.255.0 Router(config-if)#clock rate 64000 Router(config-if)#end Router#show ip interfaces brief

Router#conf t Router(config)#in f0/0 Router(config-if)#ip add 192.168.1.1 255.255.255.0 Router(config-if)#des Crossover cable to R2 Router(config-if)#no sh Router(config-if)#in s0/0/0 Router(config-if)#ip add 192.168.2.1 255.255.255.0 Router(config-if)#clo r 64000 Router(config-if)#end Router#sh ip int bri

RIP

Router(config)#router rip Router(config-router)#version 2 Router(config-router)#network 192.168.0.0 Router(config-router)#end Router#show ip route Router#show ip protocols

Router(config)#router r Router(config-router)#ve 2 Router(config-router)#net 192.168.0.0 Router(config-router)#end Router#sh ip ro Router#sh ip proto

EIGRP

Router(config)#router eigrp 1 Router(config-router)#network 192.168.0.0 Router(config-router)#no auto-summary Router(config-router)#redistribute static Router(config-router)#exit Router(config)#ip route 0.0.0.0 0.0.0.0 s0/0/0

Router(config)#router e 1 Router(config-router)#net 192.168.0.0 Router(config-router)#no au Router(config-router)#r s Router(config-router)#exit Router(config)#ip route 0.0.0.0 0.0.0.0 s0/0/0

Switchport Security

Swtich(config)#interface fastethernet 0/6 Swtich(config-if)#switchport mode access Swtich(config-if)#switchport access vlan 10 Swtich(config-if)#switchport port-security Swtich(config-if)#switchport port-security maximum 5 Swtich(config-if)#switchport port-security mac-address 1111.2222.3333 Swtich(config-if)#switchport port-security violation shutdown Swtich(config-if)#do show port-security

Swtich(config)#in f0/6 Swtich(config-if)#sw m a Swtich(config-if)#sw a v 10 Swtich(config-if)#sw po Swtich(config-if)#sw po ma 5 Swtich(config-if)#sw po mac 1111.2222.3333 Swtich(config-if)#sw po v s Swtich(config-if)#do sh por

VTP

Switch(config)#vtp version 2 Switch(config)#vtp mode client Switch(config)#vtp domain CISCO Switch(config)#vtp password cisco Switch(config)#vtp pruning Switch(config)#do show vtp status

Switch(config)#vt v 2 Switch(config)#vt m c Switch(config)#vt d CISCO Switch(config)#vt pa cisco Switch(config)#vt pr Switch(config)#do sh vt st

NAT/PAT

Router(config)#ip nat pool POOL 192.168.100.1 192.168.100.50 netmask 255.255.255.0 Router(config)#access-list 1 permit 172.168.0.0 0.0.0.255 Router(config)#ip nat inside source list 1 pool POOL overload Router(config)#interface fastethernet 0/0 Router(config-if)#ip nat inside Router(config-if)#interface fastethernet 0/0 Router(config-if)#ip nat outside

Router(config)#ip nat poo POOL 192.168.100.1 192.168.100.50 n 255.255.255.0 Router(config)#ac 1 p 172.168.0.0 0.0.0.255 Router(config)#ip nat i s l 1 p POOL o Router(config)#in f0/0 Router(config-if)#ip na i Router(config-if)#in f0/0 Router(config-if)#ip nat o

DHCP

R1(config)#ip dhcp excluded-address 10.0.0.1 10.0.0.5 R1(config)#ip dhcp pool POOL R1(dhcp-config)#network 10.0.0.0 255.255.255.0 R1(dhcp-config)#default-router 10.0.0.1 R2(config)#interface fastethernet 0/5 R2(config-if)#ip helper-address 10.10.10.5

R1(config)#ip dh e 10.0.0.1 10.0.0.5 R1(config)#ip dh po POOL R1(dhcp-config)#netw 10.0.0.0 255.255.255.0 R1(dhcp-config)#de 10.0.0.1 R2(config)#in f0/5 R2(config-if)#ip help 10.10.10.5

Trunk Links/Etherchannel

Switch(config)#interface range fastethernet 0/7 - 0/12 Switch(config-if)#switchport trunk encapsulation dot1q Switch(config-if)#switchport mode trunk Switch(config-if)#channel-group 1 mode desirable

Switch(config)#in r f0/7-0/12 Switch(config-if)#sw tru en do Switch(config-if)#sw mo tru Switch(config-if)#channel-g 1 mo de

HSRP

Switch(config)#interface vlan 10 Switch(config-if)#standby 1 ip 192.168.0.1 Switch(config-if)#standby 1 priority 100 Switch(config-if)#standby 1 preempt

Switch(config)#int vl 10 Switch(config-if)#st 1 ip 192.168.0.1 Switch(config-if)#standby 1 priority 100 Switch(config-if)#standby 1 preempt

Spanning-Tree

Switch(config)#spanning-tree mode rapid-pvst Switch(config)#spanning-tree portfast default Switch(config)#spanning-tree vlan 1 root primary Switch(config)#do show spanning-tree

Switch(config)#spanning-tree mode rapid-pvst Switch(config)#spanning-tree portfast default Switch(config)#spanning-tree vlan 1 root primary Switch(config)#do sh span