View source for Chapter Command List (chapters 1.5.1-11.6.3)

==Chapter 1.5.1 and 1.5.2 Lab Command List==


'''Show ip Interface Brief:''' Shows which interfaces have IP access lists applied in a brief format.

'''Enable:''' directs you into privileged mode.

'''Configure Terminal (config t):'''

'''Exit:''' returns 1 mode down

'''?:'''  shows list of commands in certain modes.

'''Hostname (name here):''' name of device.

'''No ip domain-lookup:''' disables DNS lookup

'''Enable secret class:''' Enables password for privileged mode.

'''No enable password:''' Disables password for privileged mode.

'''Banner motd &:''' Applies banner to accessing the device.

'''Line console #:''' Console configuration mode.

'''Line vty # #:''' (Telnet) interface configuration mode

'''Interface fastethernet #/#:''' Accessing configuration of a FastEthernet port

'''(while in interface configuration) Ip address  AAA.BBB.CCC.DDD   AAA.BBB.CCC.DDD:''' Ip address and subnet address of port.

'''No shutdown:''' Activates the port.

'''Description (name here):''' names port (for a reason)

'''Clock rate (then #):''' speed of port (for serial)

'''Interface serial #/#/#:''' Accessing configuration of Serial port.

'''End:''' back to user mode.

'''Copy running-config startup-config:''' Saves settings into NVRAM.

'''Ping:''' Tests IP connectivity to a remote device.

'''Show version:''' shows the IOS information of the switch or router, as well as the uptime.

'''Show interfaces (interface type here):'''  Shows the statistics of interface

'''Show run:''' Short for show running-config; shows the configuration currently running on the router.

'''Traceroute (address of device you want traced):''' Tests a connection to a remote device and shows the path it took through the internetwork to find the remote device including hops and IP addresses of those hops.

'''Tracert:''' same as above

'''Erase startup-config:''' Clears NVRAM and startup configurations to defult.

'''Show ip route:''' Displays the IP routing table.


==Chapter 2.8.1 and 2.8.3 Lab Command List==


'''Debug Ip routing:''' allows user to debug current problems with the device.

'''Logging synchronous:''' Stops messages from overwriting your input.

'''Exec-timeout (minutes [seconds]):''' sets the time out for console connection in minutes and seconds.

'''No debug ip routing:''' turns off debugging process.

'''Ip route (network address) (subnet address) (exit-interface):''' for static routing

'''Ip route 0.0.0.0 0.0.0.0 (ip address or interface):''' default static address.


==Chapter 4.6.1 Lab Command List==


'''Router rip:''' Enables RIP protocol on the router

'''Network (network address):''' tells the protocol what networks to connect to and show to other routers.


==Chapter 5.6.1 Lab Command List==


'''Debug ip rip:''' Displays information about RIP packets being sent and received through the router interfaces.

'''Undebug all:''' Disables all debugging processes

'''No router rip:''' Disables router RIP protocol.

'''Passive-interface (interface type):''' An interface that will not send network updates to other devices.

'''Show ip protocols:''' Shows protocols, timers that are with each routing protocol.

'''Default-information originate:'''

'''Clear ip route:'''


==Chapter 7.5.1 Lab Command List==


'''No ip cef:'''

'''Version 2:''' Activates version 2 of RIP protocol.

'''No auto-summary:''' Disables summarization.

'''Auto-summary:''' Enables summarization.


==Chapter 8.4.1 Lab Command List==


'''Shutdown:''' Turns off an interfaces in Administratively down mode.

'''No ip classless:''' Disables classless setting.

'''Ip classless:''' A global configuration command used to tell a router to forward packets to a default route when the destination network is not in the routing table.


==Chapter 9.6.1 Lab Command List==


'''Router eigrp #:''' Turns on EIGRP in the router.

'''Show ip eigrp neighbors:''' Shows neighboring routers that run EIGRP

'''Bandwidth #:''' Applying a speed to a certain Interface

'''Show ip eigrp topology:'''

'''Show ip eigrp topology (Network address):''' Gives information for the network address.

'''Interface Lo# or loopback#:''' Makes an loopback interface (primarily for troubleshooting).

'''Ip summary-address eigrp # (network address  subnet address):''' Configure manual summarization.

'''Redistribute static:''' Includes static route into EIGRP updates.


==Chapter 11.6.1 Lab Command List==


'''Router ospf #:''' Enables OSPF protocol on the router.

'''Network (ip address)(wildcard mask)(area ID):''' used to Network for the OSPF protocol.

'''Show ip ospf:''' Shows detailed information on current conditions of OSPF protocol.

'''Show ip ospf interface:''' Shows interfaces that are configured for OSPF.

'''Show ip ospf neighbor:''' Shows neighboring devices that are running the OSPF protocol.

'''Router-id AAA.BBB.CCC.DDD:'''

'''Clear ip ospf process:''' Clears OSPF from device.

'''Ip ospf cost #:''' Adds a cost to the interface or route.

'''Auto-cost reference-bandwidth #:'''