ITCwiki - User contributions [en]

Franske CNT-2722

2011-08-22T19:37:37Z

Kaschner: /* General Course Information */

This is the homepage for the CNT 2722: Building the Foundation to IP Telephony classes taught by Dr. Ben Franske.

= General Course Information =
* [[Franske CNT-2722 Syllabus|Course Syllabus]]
* [[Franske CNT-2722 FA11 Schedule|Fall 2011 Course Schedule]]
* [[Franske CNT-2722 Labs and Homework|Lab and Homework List]]
* [[Franske CNT Service Project Assignment|Service Project Assignment]]
* [[Franske Lab Report Format|Lab Report Format]]
* Assessments available at [http://class.ihcnt.net http://class.ihcnt.net]

= Projects =

= Resources =

Franske CNT-2722

2011-08-22T19:34:09Z

Kaschner: /* General Course Information */

This is the homepage for the CNT 2722: Building the Foundation to IP Telephony classes taught by Dr. Ben Franske.

= General Course Information =
[[File:Portrait1.jpg]]
* [[Franske CNT-2722 Syllabus|Course Syllabus]]
* [[Franske CNT-2722 FA11 Schedule|Fall 2011 Course Schedule]]
* [[Franske CNT-2722 Labs and Homework|Lab and Homework List]]
* [[Franske CNT Service Project Assignment|Service Project Assignment]]
* [[Franske Lab Report Format|Lab Report Format]]
* Assessments available at [http://class.ihcnt.net http://class.ihcnt.net]
[[File:Portrait1.jpg]]

= Projects =

= Resources =

File:Portrait1.jpg

2011-08-22T19:33:35Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-05-03T20:46:07Z

Kaschner:

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-int)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-int)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-int)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|ping
|ping
|-
!
|tracert
|traceroute
|-
!
|show run
|show running-config all
|-
!
|copy run start
|copy config
|-
!
|erase start
|clear config all
|-
|}
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-03-06T10:55:29Z

Kaschner:

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-int)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-int)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-int)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

Franske CNT-2612

2011-03-01T19:59:52Z

Kaschner:

This is the homepage for the CNT-2612: CCNP 1 Network Switching classes taught by Dr. Ben Franske.

= General Course Information =
* [[Franske CNT-2612 Syllabus|Course Syllabus]]
* [[Franske CNT-2612 SP11 Schedule|Spring 2011 Course Schedule]]
* [[Franske CNT-2612 Labs and Homework|Lab and Homework List]]
* [[Franske CNT Service Project Assignment|Service Project Assignment]]
* [[Franske Lab Report Format|Lab Report Format]]
* Assessments and online curriculum available at [http://cisco.netacad.net http://cisco.netacad.net]

= Projects =
* [http://wiki.ihcnt.net/w/IOS_vs._CatOS:_Basic_Configuration IOS vs. CatOS: Basic Configuration]
= Resources =

Franske CNT-2612

2011-03-01T19:58:02Z

Kaschner:

This is the homepage for the CNT-2612: CCNP 1 Network Switching classes taught by Dr. Ben Franske.

= General Course Information =
* [[Franske CNT-2612 Syllabus|Course Syllabus]]
* [[Franske CNT-2612 SP11 Schedule|Spring 2011 Course Schedule]]
* [[Franske CNT-2612 Labs and Homework|Lab and Homework List]]
* [[Franske CNT Service Project Assignment|Service Project Assignment]]
* [[Franske Lab Report Format|Lab Report Format]]
* Assessments and online curriculum available at [http://cisco.netacad.net http://cisco.netacad.net]

= Projects =
* [[IOS_vs._CatOS:_Basic_Configuration]]
= Resources =

IOS vs. CatOS: Basic Configuration

2011-02-15T23:45:59Z

Kaschner:

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:45:52Z

Kaschner:

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:45:42Z

Kaschner:

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:44:39Z

Kaschner:

[[File:Cat2960.jpg|right]][[File:Cat4006.jpg|right]]
{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|
=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:44:20Z

Kaschner:

[[File:Cat2960.jpg|right]][[File:Cat4006.jpg|right]]

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|
=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:40:30Z

Kaschner:

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:40:01Z

Kaschner:

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:39:53Z

Kaschner:

{| border="0" width="100%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:39:35Z

Kaschner:

{| border="0" width="90%" cellpadding="1"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:39:03Z

Kaschner:

{| border="0" width="90%" cellpadding="2"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:38:56Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:38:46Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:38:01Z

Kaschner:

{| border="0" width="80%"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:37:52Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:37:45Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:37:28Z

Kaschner:

{| border="0" width="80%"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|
=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:37:12Z

Kaschner:

{| border="1" width="80%"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|
=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:35:30Z

Kaschner:

{| border="1" width="80%"
| =IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
| =CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:34:57Z

Kaschner:

{| border="1" width="80%" align="top"
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|
=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:33:55Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:33:10Z

Kaschner:

{| border="1" width="80% align="center""
|
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|
=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:32:58Z

Kaschner:

{| border="0" width="80%"
|
IOS vs. CatOS: Basic Configuration
|}
{| border="1" width="80% align="center""
||
=IOS=
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
||
=CatOS=
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
= Commands =
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

= Troubleshooting =

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==
__NOTOC__

IOS vs. CatOS: Basic Configuration

2011-02-15T23:31:58Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:30:54Z

Kaschner:

{| border="0" width="80%"
|
IOS vs. CatOS: Basic Configuration
|}
{| border="1" width="80% align="center""
||
==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
||
==CatOS==
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:29:49Z

Kaschner:

{| border="0" width="80%"
|
IOS vs. CatOS: Basic Configuration
|}
{| border="0" width="80% align="center""
||
==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
||
==CatOS==
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:28:35Z

Kaschner:

{| border="0" width="80%"
|
IOS vs. CatOS: Basic Configuration
|}
{| border="0" width="80%"
||
==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
||
==CatOS==
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:27:13Z

Kaschner:

{| border="0" width="80%"
|
IOS vs. CatOS: Basic Configuration
|}
{| border="0" width="80%"
|
==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|
==CatOS==
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:26:34Z

Kaschner:

{| border="0" width="80%"
|
|}
{| border="0" width="80%"
|
==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|
==CatOS==
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:12:50Z

Kaschner:

{| border="0" width="80%"
|
==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|

==CatOS==
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:12:32Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:12:26Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:12:21Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:12:15Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:12:07Z

Kaschner:

IOS vs. CatOS: Basic Configuration

2011-02-15T23:11:27Z

Kaschner:

{| border="0" width="80%"
|
==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|
==CatOS==
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:09:34Z

Kaschner:

{| border="0" width="80%"
|==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|==CatOS==
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:09:20Z

Kaschner:

{| border="0" width="50%"
|==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|==CatOS==
CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
[[File:Cat4006.jpg|right]]
|}
== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:08:57Z

Kaschner:

{| border="0" width="50%"
|==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|==CatOS==
[[File:Cat4006.jpg|right]]

CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
|}

[[File:Cat4006.jpg|right]]

== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:08:30Z

Kaschner:

{| border="0" width="50%"
|==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
[[File:Cat2960.jpg|right]]
|==CatOS==
[[File:Cat4006.jpg|right]]

CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
|}

== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:07:11Z

Kaschner:

{| border="0" width="50%"
|==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
|[[File:Cat2960.jpg|right]]
|==CatOS==
|[[File:Cat4006.jpg|right]]

CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
|}

== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:06:49Z

Kaschner:

{| border="0" width="80%"
|==IOS==
IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
|[[File:Cat2960.jpg|right]]
|==CatOS==
|[[File:Cat4006.jpg|right]]

CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
|}

== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:06:09Z

Kaschner:

{| border="0" width="80%"
|==IOS==
[[File:Cat2960.jpg|right]]

IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.
|[[File:Cat2960.jpg|right]]
|==CatOS==
|[[File:Cat4006.jpg|right]]

CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
|}

== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==

IOS vs. CatOS: Basic Configuration

2011-02-15T23:05:01Z

Kaschner:

{| border="0" width="80%"
==IOS==
[[File:Cat2960.jpg|right]]

IOS (Internetwork Operating System) is the operating system primarily used for the majority of Cisco's current equipment, including Routers and Switches.

IOS uses different configuration modes, depending on what your currently configuring. For example - if you wanted to turn a port on in IOS, you would first need to be in priviledged exec -> global configuration -> and move into interface configuration, then issue the ''no shutdown'' command.

==CatOS==
[[File:Cat4006.jpg|right]]

CatOS is the operating system used on Cisco's Catalyst switches before changing over to IOS. Before purchasing the technology from Crescendo in 1993, CatOS was called XDI. CatOS is a Unix-like operating system for many legacy Cisco switches. CatOS runs on the following switch series: 1200, 4000, 4500, 5000, 5500, 6000 and 6500. Some of the high end switches such as the Catalyst 6500 series still run CatOS.

User mode is used for system monitoring. Priviledged (enable) mode is used to change all system configurations. All configurations in CatOS are done by a ''set'' command sequence.
|}

== Commands ==
On this page we will be comparing two switches; a Catalyst 2960 running IOS and a Catalyst 4006 running CatOS.

In IOS, the user is required to issue a command to save to NVRAM.

Commands entered in CatOS are committed to NVRAM instantaneously.
{| border="0" width="80%"
|-
!
! IOS Command
! CatOS Command
|-
!Privileged
| Enable
| Enable
|-
!Interface
| (config-t)interface ''int'' (which puts you into interface configuration mode)
| (enable)set port ''command'' ''mod/port''
|-
!Set Console Password
| (config-line)password ''password''
| (enable)set password (you will be prompted to change password)
|-
!Turn on ports
| (config-if)no shutdown
| (enable)set port enable ''mod/port''
|-
!Turn off ports
| (config-if)shutdown
| (enable)set port disable ''mod/port''
|-
!Banner-MOTD
| (config-t)banner-motd # ''banner here'' #
| (enable)set banner motd # ''banner here'' #
|-
!Clear Banner
| (config-t)
| (enable)clear banner motd
|-
!System / Hostname
| (config)hostname ''name''
| (enable)set system name ''name''
|-
!Set Idle Logout time
| (config-t)
| (enable)set logout ''time'' (in minutes)
|-
!Bandwidth
| (config-if)bandwidth ''number in kb''
| (enable)set port speed ''speed in megabits''
|-
!Setting up a domain name for VTP
| (config-t)vtp domain ''domain-name''
| (enable)set vtp domain ''domain-name''
|-
!Enabling VLANS
| (config-t)vlan ''number'' (will put switch into sub-config mode, but the vlan will become active)
| (enable)set vlan ''number'' state ''active''
|-
!VLAN names
| (config-vlan)name ''name''
| (enable)set vlan ''vlan number'' name ''name''
|-
!Delete VLANS
| (config-t)no vlan ''number''
| (enable)clear vlan ''number''
|-
!Enabling Trunking
| (config-int)switchport mode trunk
| (enable)set trunk ''mod_num/port_num [on/off/desirable/auto/nonegotiate] [vlan_range] [isl/dot1q/dot10/lane/negotiate]
|-
!Clear Trunking
| (config-int)no switchport mode trunk
| (enable)clear trunk ''mod/port'' ''vlan range''
|-
!Delete files from Flash Device
| (enable)delete flash:''filename''
| (enable)delete bootflash:''filename''
|-
!Spanning-Tree
| (config-t)spanning-tree ''vlan''
| (enable)set spantree enable all
|-
|}

== Troubleshooting ==

{|border="0" style="width:400px"
!
!IOS Command
!CatOS Command
|-
!
|Ping
|
|-
!
|tracert
|
|-
!
|show ip route
|
|-
!
| show int ''int''
|
|-
!
|show run
|
|-
!
|copy run start
|
|-
!
|erase start
|
|-
|}

[[File:]]

==
'''WIP''' ==